Question

What will an OSPF router prefer to use first as a router ID?

Question

Match the description to the term.

  1. This is where the details of the neighboring routers can be found. → Adjacency database
  2. This is the algorithm used by OSPF. → Shortest Path First
  3. All the routers are in the backbone area. → Single-area OSPF
  4. This is where you can find the topology table. → Link-state database

Question

Match the OSPF state with the order in which it occurs.

  1. second state → Init state
  2. seventh state → Full state
  3. fifth state → Exchange state
  4. first state → Down state
  5. fourth state → Exstart state
  6. third state → Two-way state
  7. sixth state → Loading state

Question

What are the two purposes of an OSPF router ID? (Choose two.)

Question

In an OSPFv2 configuration, what is the effect of entering the command network 192.168.1.1 0.0.0.0 area 0?

Question

What is the reason for a network engineer to alter the default reference bandwidth parameter when configuring OSPF?

Question

A network engineer has manually configured the hello interval to 15 seconds on an interface of a router that is running OSPFv2. By default, how will the dead interval on the interface be affected?

Question

The graphic shows a router R1 connected to a switch. The switch is connected to another router R2. Below R1 there is a label with the text: Hello Timer: 5 Dead Interval: 20. Below R2 there is a label with the text: Hello Timer: 25 Dead Interval: 100.

Refer to the exhibit. A network administrator has configured the OSPF timers to the values that are shown in the graphic. What is the result of having those manually configured timers?

Question

There are 4 routers connected to a centrally located switch. Near R1 there is a tag with the following information: Router-ID: 1.1.1.1 FastEthernet 0/0: 192.168.1.3 FastEthernet 0/0 priority: 1 Serial 0/0/0: 10.0.2.1 Loopback 0: 172.16.1.3 Near R2 there is a tag with the following information: Router-ID: Not configured FastEthernet 0/0: 192.168.1.5 FastEthernet 0/0 priority: 255 Serial 0/0/0: 10.0.3.1 Loopback 0: Not configured Near R3 there is a tag with the following information: Router-ID: Not configured FastEthernet 0/0: 192.168.1.4 FastEthernet 0/0 priority: 1 Serial 0/0/0: 10.0.1.1 Loopback 0: Not configured Near R4 there is a tag with the following information: Router-ID: Not configured FastEthernet 0/0: 192.168.1.2 FastEthernet 0/0 priority: Default Serial 0/0/0: 10.0.1.1 Loopback 0: 172.16.1.1

Refer to the exhibit. Which three statements describe the results of the OSPF election process of the topology that is shown in the exhibit? (Choose three.)

Question

By default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater?

Question

The graphic contains four routers, labeled A, B, C, and D, which are connected to each other through a switch. They are all connected to the switch through their GigabitEthernet0/0 interfaces. Router A has router ID 4.4.4.4 and is connected to LAN 172.16.2.0/24. Router B has router ID 2.2.2.2 and is connected to LAN 172.16.4.0/24. Router C has router ID 1.1.1.1 and is connected to LAN 172.16.1.0/24. Router D has router ID 3.3.3.3 and is connected to LAN 172.16.3.0/24.

Refer to the exhibit. Suppose that routers B, C, and D have a default priority, and router A has a priority 0. Which conclusion can be drawn from the DR/BDR election process?​

Question

What is used to facilitate hierarchical routing in OSPF?

Question

The graphic shows a network of two routers running OSPF connected in the following ways. Router Branch1 has the following interfaces configured:  G0/0 is connected to a switch and a host. The IP address of G0/0 is 10.1.0.1/16. Another Ethernet interface is connected to router Branch2 with a switch in between.  This interface IP is 10.0.0.1/16. There is a loopback interface with IP address 192.168.1.100, and there is a serial interface connected to the cloud with IP address 209.165.201.1/29  Router Branch2 has the following interfaces configured: There is an Ethernet interface connected to router Branch1 with a switch in between.  This interface IP is 10.0.0.2/16. There is a serial interface with IP address 209.165.201.2/29 connected to the cloud.

Refer to the exhibit. If no router ID was manually configured, what would router Branch1 use as its OSPF router ID?

Question

An OSPF router has three directly connected networks; 172.16.0.0/16, 172.16.1.0/16, and 172.16.2.0/16. Which OSPF network command would advertise only the 172.16.1.0 network to neighbors?

Question

Graphic Description The network consists of four OSPF routers connected to a single Ethernet LAN via a Layer 2 switch. All four routers are connected to the LAN, which is in network 10.0.0.0/16 Each router also has a loopback interface and a router ID as follows:    router R1 loopback 0 IP address:192.168.1.100/32 Ethernet LAN IP address: 10.0.0.1/16 router ID: 1.1.1.1 priority = 2  router R2 loopback 0 IP address:192.168.2.100/32 Ethernet LAN IP address: 10.0.0.2/16 router ID: 2.2.2.2 priority = 2  router R3 loopback 0 IP address: 192.168.3.100/32 Ethernet LAN IP address: 10.0.0.3/16 router ID: 3.3.3.3 priority = 1  ROuter R4 Loopback 0 IP address is 192.168.4.100/32 Ethernet LAN IP address 10.0.0.4/16 router ID is 4.4.4.4 Priority = 1

Refer to the exhibit. If the switch reboots and all routers have to re-establish OSPF adjacencies, which routers will become the new DR and BDR?

Question

This graphic contains the following information: There are three routers labeled A, B, and C,  which are connected to each other through serial links. A is connected to B through a 1544 Kbps serial link, and is connected to C through a 64 Kbps serial link. A is also connected to the LAN 172.16.1.0/24 through a Gigabit Ethernet interface G0/0. B is connected to C through a 1544 Kbps serial link. It is also connected to the LAN 172.16.2.0/24 through a Gigabit Ethernet interface G0/0. C is also connected to the LAN 172.16.3.0/24 through a Gigabit Ethernet interface G0/0.

Refer to the exhibit. What is the OSPF cost to reach the router A LAN 172.16.1.0/24 from B?

Question

What command would be used to determine if a routing protocol-initiated relationship had been made with an adjacent router?

Question

After modifying the router ID on an OSPF router, what is the preferred method to make the new router ID effective?

Question

A network technician issues the following commands when configuring a router:
R1(config)# router ospf 11
R1(config-router)# network 10.10.10.0 0.0.0.255 area 0

What does the number 11 represent?

Question

The exhibit shows a cloud labeled "The World" in the upper left corner. Within that cloud is a router labeled ISP. The ISP router connects through a serial connection to a router labeled R0-A.  R0-A and two other routers and three switches are contained within a circle labeled OSPF Area 0. R0-A connects to a switch. That same switch has a connection to R0-B (that has a separate connection to another switch) and R0-C (that has a separate connection to another switch).

Refer to the exhibit. On which router or routers would a default route be statically configured in a corporate environment that uses single area OSPF as the routing protocol?

Question

The exhibit shows the following output: Serial0/0/1 is up, line protocol is up   Internet Address 172.16.30.1/30, Area 0, Attached via Network Statement   Process ID 10, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 64   Topology-MTID    Cost    Disabled    Shutdown      Topology Name         0           64        no          no            Base   Transmit Delay is 1 sec, State POINT_TO_POINT   Timer intervals configured, Hello 5, Dead 20, Wait 20, Retransmit 5     oob-resync timeout 40     Hello due in 00:00:02   Supports Link-local Signaling (LLS)   Cisco NSF helper support enabled   IETF NSF helper support enabled   Index 2/2, flood queue length 0   Next 0x0(0)/0x0(0)   Last flood scan length is 1, maximum is 1   Last flood scan time is 0 msec, maximum is 0 msec   Neighbor Count is 1, Adjacent neighbor count is 1     Adjacent with neighbor 1.1.1.1   Suppress hello for 0 neighbor(s)   Message digest authentication enabled     Youngest key id is 1 R1#

Refer to the exhibit. Which command did an administrator issue to produce this output?

Question

Which command is used to verify that OSPF is enabled and also provides a list of the networks that are being advertised by the network?​

Question

Which command will a network engineer issue to verify the configured hello and dead timer intervals on a point-to-point WAN link between two routers that are running OSPFv2?

Question

What is a benefit of multiarea OSPF routing?

Question

The graphic displays the following: Router R1 is connected to PC1 and has the IP address 192.168.10.254 on interface Fa0/0. PC1 has the IP address 192.168.10.1 /24. Router R1 S0/0 has IP address 192.168.20.1 /30 and is connected to router R2 on interface S0/0 with IP address 192.168.20.2 /30. Router R2 is connected to PC1 and has the IP address 192.168.30.254 on interface Fa0/0. PC2 has the IP address 192.168.30.1 /30. Below the topology is a router prompt and command, and some partial command output: R2# show ip protocols <output omitted> Routing Protocol is "ospf 99"   Router ID 192.168.30.254   Maximum path: 4   Routing for Networks:     192.168.20.2 0.0.0.0 area 0     192.168.3.0 0.0.0.255 area 0   Passive Interface(s):     FastEthernet0/0   Routing Information Sources:       Gateway         Distance      Last Update     192.168.20.1         110      00:02:11     192.168.30.254       110      00:02:11   Distance: (default is 110)

Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers but PC1 is unable to connect to PC2. What is the most likely problem?

Question

What indicates to a link-state router that a neighbor is unreachable?

Question

Match each OSPF packet type to how it is used by a router.

  1. hello packet → establish and maintain adjacencies
  2. link-state update packet → advertise new information
  3. database description packet → compare local topology to that sent by another router
  4. link-state request packet → query another router for additional information

Question

Which OSPF data structure is identical on all OSPF routers that share the same area?

Question

  PT Activity

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
 
Which task has to be performed on Router 1 for it to establish an OSPF adjacency with Router 2?

Question

Which step does an OSPF-enabled router take immediately after establishing an adjacency with another router?

Question

To establish a neighbor adjacency two OSPF routers will exchange hello packets. Which two values in the hello packets must match on both routers? (Choose two.)

Question

Which three OSPF states are involved when two routers are forming an adjacency? (Choose three.)

Question

What is the format of the router ID on an OSPF-enabled router?

Question

In an OSPF network when are DR and BDR elections required?

Question

What is the default router priority value for all Cisco OSPF routers?

Question

Which type of OSPFv2 packet contains an abbreviated list of the LSDB of a sending router and is used by receiving routers to check against the local LSDB?

Question

When an OSPF network is converged and no network topology change has been detected by a router, how often will LSU packets be sent to neighboring routers?

Question

What is the recommended Cisco best practice for configuring an OSPF-enabled router so that each router can be easily identified when troubleshooting routing issues?

Question

Which step in the link-state routing process is described by a router running an algorithm to determine the best path to each destination?

Question

Which step in the link-state routing process is described by a router inserting best paths into the routing table?

Question

Which step in the link-state routing process is described by a router sending Hello packets out all of the OSPF-enabled interfaces?

Question

Which step in the link-state routing process is described by a router flooding link-state and cost information about each directly connected link?

Question

Which step in the link-state routing process is described by a router flooding link-state and cost information about each directly connected link?

Question

Which step in the link-state routing process is described by a router building a link-state database based on received LSAs?

Question

Which step in the link-state routing process is described by a router building a link-state database based on received LSAs?

Question

Which step in the link-state routing process is described by a router running an algorithm to determine the best path to each destination?

Question

Which step in the link-state routing process is described by a router building a link-state database based on received LSAs?

Question

Which step in the link-state routing process is described by a router running an algorithm to determine the best path to each destination?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.102.0.0 255.255.255.128. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.102.0.0 255.255.255.128. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.223.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 192.168.181.0 255.255.254.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 198.19.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 198.19.0.0 255.255.252.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 64.100.0.0 255.255.255.0. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.255.192. What wildcard mask would the administrator use in the OSPF network statement?

Question

An administrator is configuring single-area OSPF on a router. One of the networks that must be advertised is 128.107.0.0 255.255.255.192. What wildcard mask would the administrator use in the OSPF network statement?